Grime is the sound of London. Born in the early 2000s from the UK garage scene in East London, it took the tempo of garage, stripped the swing down to something cold and skeletal, and gave MCs a sparse, aggressive canvas to spit over. At its core, grime is a 140 BPM problem — and getting the feel right matters more than any single sound.
This guide walks through the whole thing: setting your project up at 140, programming the drums that define grime, designing the square-wave bass, building the iconic 8-bar "eskibeat", and arranging an instrumental that leaves room for an MC. Whether you're in FL Studio, Ableton or Logic, the principles translate.
Setting Up Your Project at 140 BPM
Grime lives at 140 BPM, shared with dubstep but feeling completely different. Where dubstep drops into half-time weight, grime stays snappy and forward-moving. Set your project to exactly 140 before anything else.
The first trap beginners fall into is making grime too dense. Grime is sparse. The space between the kick, the snare and the bass is part of the sound — it's what gives an MC room to ride the beat. If you're filling every gap, you're making UK drill or trap, not grime.
Programming the Drums
Grime drums are built around a specific felt relationship. The kick holds the low end, but it's the snare and the ghost patterns around it that give grime its snap. Here's the foundational pattern, grid as 16th notes at 140 BPM:
- Kick: Beat 1, plus a syncopated hit on the "and" of beat 3 for forward motion
- Snare/clap: Beats 2 and 4 — this is your gunshot backbeat, the spine of the track
- Ghost snares: Light hits on 16ths just before and after the main snare, low velocity
- Hi-hats: 8th notes, tight and closed — grime hats are crisp, not washy
The snare sound is everything. Grime snares are sharp, dry and almost aggressive — think a snare with the body stripped back and a hard transient up front. If yours sounds soft, layer in a clap or rimshot for the initial crack, and high-pass the layer to keep it out of the bass's way.
Designing the Grime Bass
Grime bass is usually a square wave — cold, hollow and a little bit nasal. It's the polar opposite of the warm, rounded reese bass you'd build for drum and bass. The square wave gives grime its characteristic "buzz" that sits right under the vocal.
Open any subtractive synth (Operator in Ableton, 3xOSC in FL Studio, any stock synth). The basic recipe:
- Oscillator: Square wave, no detune — keep it monophonic
- Filter: Low-pass, cutoff around 250–400Hz so it sits low and menacing
- Filter envelope: Fast attack, sustain low enough that the note decays naturally
- Amp envelope: Instant attack, medium decay — grime bass is punchy and short, not sustained
Writing the Bassline
Grime basslines are simple and repetitive. You're not writing a melody here — you're writing a hook that the MC and the listener lock onto. Most classic eskibeat basslines are 2 to 4 notes, repeating an 8-bar loop with tiny variations at the end of the phrase.
Keep the bass an octave below the melody stab if you're using one, and leave rests on the snare hits. The bass should answer the kick, not smear over it.
The Iconic 8-Bar Eskibeat
"Eskibeat" is the term coined by Wiley for the cold, sparse 8-bar instrumental structure that defined early grime. The 8-bar isn't just a length — it's the signature grime move where the beat suddenly changes at bar 8, dropping the melody and switching to a hard, minimal groove for the MC to take over.
Here's how to build it. An 8-bar grime loop typically works like this:
- Bars 1–6: Main groove, with the melody or melodic stab present
- Bar 7: A one-bar fill or variation — an extra snare roll, a reverse cymbal, a drop in the drums
- Bar 8: The "switch" — melody cuts out, drums and bass go hard and minimal
The switch at bar 8 is what makes it an eskibeat rather than just a loop. It's the moment an MC knows to come in, and it's the moment the energy spikes. In a full track, you build the whole arrangement around these 8-bar units, chaining them with small variations so the beat never feels static.
Arranging a Grime Instrumental for an MC
Grime is MC-led. The instrumental's job is to create a rhythmic bed with enough space for a vocal to sit on top — not to fill the spectrum the way an instrumental electronic track would. Here's a typical structure for a grime instrumental, in 8-bar sections:
- 0:00 – 0:22 (16 bars): Intro — drums and bass only, or a filtered version of the main groove
- 0:22 – 1:07 (32 bars): First verse — full groove, minimal melody, maximum space for the MC
- 1:07 – 1:30 (16 bars): Hook/chorus — the most memorable 8-bar loop, melody present
- 1:30 – 2:15 (32 bars): Second verse — same bed, with a subtle variation to keep energy
- 2:15 – 2:38 (16 bars): Outro — strip back to drums and bass, tail out
The golden rule: when an MC is on the track, the bass is your main harmonic element — keep pads and chords out, or so low in the mix they're barely felt. Grime beats are about impact and space, not texture.
Finishing Your Grime Beat
Grime mixes differently to other bass music. The bass needs to be present but controlled — a muddy low end kills an MC's vocal clarity. Keep your square-wave bass's low end in check with a high-pass around 40Hz, and make sure the snare's transient is cutting through above the bass.
Mix at a lower level than you think you need to. Grime listeners expect loud, but loudness comes from the relationship between the kick, snare and bass staying clean — not from slamming a limiter. Once the drums and bass sit right, the track will feel loud at a reasonable level.
When your beat is solid, record an MC over it. Grime is a collaborative, MC-first scene, and hearing a vocal on your instrumental will instantly tell you whether the space is working. Labels, radio (Rinse FM, BBC 1Xtra) and the wider scene all run on that energy first.
Want More UK Production Guides?
Browse our full library — from grime and drum & bass to UK garage production.